Collision Theory
Simulate colliding particles and see how temperature and concentration change the reaction rate
Live counts
- Time
- 0.0 s
- A / B left
- 40 / 40
- Products C + D
- 0 + 0
- All collisions
- 0
- A–B collisions
- 0
- …with E ≥ Ea
- 0
- Successful
- 0
- Rate (last 5 s)
- 0.00 /s
- Gas temperature
- 300 K(from mean KE)
Collision theory check
- Ea in use
- 6.0 kJ/mol
- Ea / RT
- 2.41
- Energetic share
- –(e^(−Ea/RT) = 9.0%)
- Success share
- –(predicted 9.0%)
Number of particles vs time
Maxwell-Boltzmann energy distribution
- Fraction of molecules with E ≥ Ea
- 18.6%
Why reactions happen at the rate they do
Collision theory pictures a gas-phase reaction such as A + B → C + D as a crowd of molecules flying around and bumping into each other. Most collisions are just bounces: the molecules exchange energy and fly apart unchanged. Only a small share of collisions are both hard enough and correctly lined up to rearrange the bonds and make products.
So the rate is the number of collisions per second multiplied by the fraction that succeed. The collision frequency grows with the concentration of each reactant, which is where rate laws like rate = k[A][B] come from. The successful fraction depends on the activation energy Ea and the temperature through the Boltzmann factor e^(−Ea/RT), and on the steric factor p.
In the simulation each A–B collision is tested the same way: the relative kinetic energy along the line of centres is compared with Ea, and, if orientation is switched on, the dark reactive side of A must face B. The panel on the right counts how many collisions pass each test, so you can check the observed shares against the predictions.
They must collide
With enough energy
In the right orientation
Temperature matters most
Key formulas
Collision theory rate
rate = Z_AB × p × e^(−Ea/RT)
- Z_AB
- A–B collisions per unit volume per second, proportional to [A][B]√T
- p
- steric (orientation) factor, between 0 and 1
- Ea
- activation energy (J/mol)
- R
- gas constant, 8.314 J/(mol·K)
Fraction of collisions with enough energy
f = e^(−Ea/RT)
- f
- share of collisions whose line-of-centres energy is at least Ea
Fraction of molecules with E ≥ Ea (Maxwell-Boltzmann, 3D)
F = erfc(√x) + 2√(x/π) e^(−x) (the shaded area in the distribution chart)
- x
- Ea / RT
What changes the rate, and how
| Change | Collision frequency | Fraction with E ≥ Ea | Rate |
|---|---|---|---|
| Higher concentration | Up, ∝ [A][B] | Unchanged | Up in proportion |
| Higher temperature | Up a little, ∝ √T | Up sharply, e^(−Ea/RT) | Up sharply |
| Catalyst | Unchanged | Up (lower Ea) | Up |
| Larger surface area (solids) | Up | Unchanged | Up |
| T (K) | e^(−Ea/RT) | Relative to 300 K |
|---|---|---|
| 300 | 1.97 × 10⁻⁹ | 1 |
| 310 | 3.76 × 10⁻⁹ | 1.91 |
| 350 | 3.45 × 10⁻⁸ | 17.5 |
| 400 | 2.95 × 10⁻⁷ | 150 |
| 500 | 5.98 × 10⁻⁶ | 3040 |
How to use this visualizer
- 1Watch the box: blue A and orange B particles bounce around. A red ring marks every successful collision, which turns A into green C and B into purple D.
- 2Raise the temperature. The particles speed up, the shaded tail of the Maxwell-Boltzmann chart grows, and the reaction rate jumps.
- 3Change the number of A or B particles (this restarts the run). More particles give more collisions per second and a faster start.
- 4Raise Ea and watch the energetic share of collisions fall. Compare it with the predicted e^(−Ea/RT) in the side panel.
- 5Switch on the catalyst. Ea is halved, the red line moves left, and many more collisions succeed even though the collision count is unchanged.
- 6Switch on orientation. Now A has a reactive side, and only about a third of the energetic collisions succeed: the steric factor p = 1/3.
- 7Use the particles-vs-time chart to see the rate slow down as the reactants are used up.
How the simulation is simplified
The particles move in two dimensions, all have the same mass, and the walls are held at the chosen temperature, so the gas stays at T even when you change it. Products keep their velocities, so the reaction releases or absorbs no heat. Speeds are scaled to be visible, but every energy test uses the real ratio Ea/RT. The distribution chart shows the usual three-dimensional Maxwell-Boltzmann curve for a gas, as drawn in textbooks.Common misconception
Heating does not speed reactions up mainly by making molecules collide more often. Collision frequency only grows as √T: from 300 K to 310 K that is about 1.7% more collisions. For Ea = 50 kJ/mol the fraction of collisions with enough energy almost doubles over the same 10 K. Nearly all of the temperature effect comes from the energy tail.Practice problems
Problem 1: A 10 K rise
Show solutionHide solution
ratio = e^(−Ea/R·310) / e^(−Ea/R·300) = exp[(Ea/R)(1/300 − 1/310)]
Ea/R = 50 000 / 8.314 = 6014 K
1/300 − 1/310 = 1.0753 × 10⁻⁴ K⁻¹
exponent = 6014 × 1.0753 × 10⁻⁴ = 0.6467, so ratio = e^0.6467 ≈ 1.91
collision frequency factor = √(310/300) = 1.017
Energetic fraction × 1.91; rate × 1.91 × 1.017 ≈ 1.94
Problem 2: Predict the simulation
Show solutionHide solution
Ea/RT = 10 000 / (8.314 × 500) = 2.406
e^(−2.406) = 0.0902, so 9.0% of collisions have enough energy
success share = p × 0.0902 = 0.0902 / 3 = 0.0301
reactions per second = 120 × 0.0301 ≈ 3.6
About 3.0% of A–B collisions succeed, roughly 3.6 reactions per second
Related visualizations
Discussion
Questions, ideas or a different approach? Join the conversation.